ISO9001 ISO14001
    Solution provider with 15 years in adhesive&sealant industry

Flexible skin adhesive catalyzed transparent silicone elastomer

SATOP® Two Component Flexible skin adhesive-8821

silicone elastomer
silicone elastomer
silicone elastomer

Product description of silicone elastomer

SATOP®8821 Flexible skin adhesive is a two component platinum catalyzed transparent silicone elastomer. After A, B component is mixed, it is cured to form a soft adhesive material that has a cushioning adhesive skin that can be removed. The adhesive has unique physical properties and suitable for adhesion and self-adhesive materials used in biomedical applications.The elastomer adhesive consists of platinum-catalyzed polydimethylsiloxane. Curing temperature range: at room temperature to 200 ℃, and no by-products.

  1. Solvent-free two-component system
  2. Transparent before and after curing
  3. platinum catalytic curing system
  4. No curing byproduct
  5. low viscositybefore curing, easy to processing
  6. Excellent softness, no stress
  7. Very low oil permeability after curing, excellent anti-toxicity
  8. Adhesive adhesion can be adjusted by adjusting the ratio of AB material
  9. Repeatable paste
  10. Can use polyethylene release film
  11. Through tests of physiological compatibility, toxiccells, skin irritation, etc.

Features before cured:

ItemPart A Part B
Composition PolysiloxanesHydrogen-containing polysiloxanes
AppearanceColorless transparent
liquid
Colorless transparent
liquid
Viscosity,25℃ CPS950±150550±150
Specific Gravity, g/cm30.990.99
Mixing ratioA:B =100:(80-120)A:B =100:(80-120)
Mix viscosity, mPa·s(25℃)800±150800±150
Operating time after mixing> 60 mins> 60 mins
Hardening conditions, ℃/hr25℃/ 360 mins or 120℃/ 5 mins25℃/ 360 mins or 120℃/ 5 mins
Hardened appearanceColorless clear gelColorless clear gel

Features before cured:

AppearanceColorless transparent gelColorless transparent gel
Temperature range, ℃– 60 ∽ 200– 60 ∽ 200

Typical applications

  • Suitable for boding with skin, can be used for wound dressing, eliminating scar paste, eye sticker, Etc.
  • Can also be used to fill heads, lumbar cushions, etc.

Package

Part A: 20kg/barrel; Part B: 20kg/barrel

Part A: 200kg/barrel; Part B: 200kg/barrel

Storage and transportation

  • 1 Part A and part B need to avoid light, heat, save after sealed. (Can be used as the non-dangerous goods transport and storage)
  • Shelf life : 1 years (25℃)
  • For a long period of time, there will be precipitation, which can be used after stirring. This phenomenon is not a quality problem.

How to use of  silicone elastomer

  • Weigh part A and part B by 1:1, mix well, after standing for 10mins, gently inject into the side of the wall to reduce the bubble formation.  
  • Put the encapsulated element in place for some time. After the bubble disappears, it can be heated and solidified (about 2-5 minutes at 120°C, depending on the thickness of the adhesive layer), or solidified directly at room temperature, which requires about 4hr-6hr.

Attention of operation of  silicone elastomer

  • It can be improve hardening performance if remove the bubblesafter mixing part A and part B.
  • Seal preservation after taking part A and part B
  • can lead to slow curing speed under the too low temperature and recommended workshop temperature.
  • SATOP®8821 is difficult to harden and contact with materials such as sulfur, amine, organic tin and unsaturated hydrocarbon plasticizer. Common substances have rosin, natural rubber, before use must be tested.

Product safety information is not included here. Before use, please read the product information, product safety information and packaging label for safe use. The product safety information can be obtained from SATOP and the distributor, or write to the SATOP service center [email protected] or call 021-64243697.

The technical data of this paper are all typical values obtained under laboratory conditions.We are not responsible for the results of methods beyond our control.Because users use condition is different, different material surface state, curing conditions, storage conditions, transportation and other factors can make gum stability and physical and mechanical properties, the actual performance data has some changes are normal phenomenon.Before using this product,Validation is based on the data provided in this article.If you have any problems with the process, you can contact our technical service department and we will provide you with all the help. Our company reserves the right to modify the data in this article.

 

 

  • Client :
  • Construction Date :
  • Investors Website :
  • Location :
  • Value :