ISO9001 ISO14001
    Solution provider with 15 years in adhesive&sealant industry

fire-proof silicone gel for Automotive electronics modules

SATOP® self adhered Thermal conductivity fire-proof silicone gel-8830

silicone gel
silicone gel
silicone gel

Product feature and application of silicone gel

SATOP®8830 self adhered Thermal conductivity fire-proof silicone gel is a two-component addition type potting compound, it has good liquidity after mixing. operation time can be adjusted according to the temperature, can be deeply solidified in the room temperature. Suitable for all kinds of heat dissipation and temperature resistant components, it is in accordance with EU ROHS directive and SVHC REACH. Characteristic of silicone gel:

  1. Two-component addition type silicone sealant
  2. Mixing ratio: 1:1
  3. Low hardening shrinkage
  4. Excellent high temperature electrical insulation and stability.
  5. Good waterproof and moisture-proof.    
  6. Excellent flame retardancy.

Features before cured:

ItemTest standard Part A Part B
AppearanceVisualBlack sticky liquidBlack sticky liquid
Viscosity,cps , 25℃GB/T 10247-20084500±5004500±500
Density,g/cm3, 25℃GB/T 15223-19941.5±0.031.5±0.03
Mix ratioMass ratioA:B = 100:100A:B = 100:100
Mix viscosity,cps , 25℃GB/T 10247-20084500±5004500±500
Operating time mins, 25℃GB/T 10247-200830±530±5
Curing conditionsGB/T 10247-200825℃/24 hr or 80℃/ 30mins25℃/24 hr or 80℃/ 30mins

Features after cured:

ItemTest standard Black elastomer
AppearanceVisualBlack elastomer
Penetration,0.1mmGB/T 4509-201045
Thermal conductivity,W/mK%0.68
Linear expansion coefficient,K-1,ppmGB/T 10297-1998300
Dielectric strength,kV/mm, 25℃HGT 2625-1994≥20
Volume resistance,DC 500V, Ω·CMGB/T 1695-20051.×1014
180(aluminum),lbf/inGB/T 1692-920.6
Dielectric constant (1 MHz)GB/T 2791-19953.0
Temperature range,  ℃GB/T 20028-2005– 60 ∽ 200
Flame resistanceUL-94V-0

Remark:All the above data come from 25 ℃ and 55% RH glue curing conditions after 7 days. 

Package

Part A: 10kg/barrel, 20kg/barrel

Part B: 10kg/barrel, 20kg/barrel

Storage and transportation

  • 1 Part A and part B need to avoid light, heat, save after sealed. (Can be used as the non-dangerous goods transport and storage)
  • Shelf life : 1 years (25℃)
  • For a long period of time, there will be precipitation, which can be used after stirring. This phenomenon is not a quality problem.
  • Application of silicone gel:
    1. Automotive electronics, modules.
    2. LED power driver module.
    3. Solar module junction box.
    4. Electric vehicle charging column module.
    5. Lithium battery and capacitor bank.
    6. Magnetic induction coil
    7. Inverter power supply

How to use:

  • The glue will cause precipitation if placed too long, mix part A and part B in each package before construction.
  • Weigh part A and part B by 1:1, mix well, direct injection into components (or modules). It is best to gently inject into the side of the wall to reduce the bubble formation.
  • Put the encapsulated element in place for some time. After the bubble disappears, it can be heated and solidified, or solidified directly at room temperature, which requires about 4hr.

Attention of operation

  • It can be improve hardening performance if remove the bubblesafter mixing part A and part B.
  • Seal preservation after taking part A and part B
  • can lead to slow curing speed under the too low temperature and recommended workshop temperature.
  • SATOP®8830 is difficult to harden and contact with materials such as sulfur, amine, organic tin and unsaturated hydrocarbon plasticizer. Common substances have rosin, natural rubber, before use must be tested.

Product safety information is not included here. Before use, please read the product information, product safety information and packaging label for safe use. The product safety information can be obtained from SATOP and the distributor, or write to the SATOP service center [email protected] or call 021-64243697.

The technical data of this paper are all typical values obtained under laboratory conditions.We are not responsible for the results of methods beyond our control.Because users use condition is different, different material surface state, curing conditions, storage conditions, transportation and other factors can make gum stability and physical and mechanical properties, the actual performance data has some changes are normal phenomenon.Before using this product,Validation is based on the data provided in this article.If you have any problems with the process, you can contact our technical service department and we will provide you with all the help. Our company reserves the right to modify the data in this article.

  • Client :
  • Construction Date :
  • Investors Website :
  • Location :
  • Value :