ISO9001 ISO14001
    Solution provider with 15 years in adhesive&sealant industry

silicone glue for electronics and fix Electronic component

SATOP® Dealcohol type paste neutral silicone sealant-8739

silicone glue for electronics
silicone glue for electronics
silicone glue for electronics

Description of silicone glue for electronics

SATOP®8739 is a Dealcohol type neutral silicone sealant that absorbs moisture from air at room temperature.It has good adhesion sealing property to most materials, to protect electronic products under stringent conditions.

 

Elastomer of SATOP®8739 has the following characteristics: 

  1. Excellent chemical resistance, low odor, good adhesion.
  2. Low volatiles of no more than 500ppm, airtight environment no corrosion no fog.
  3. Reduce mechanical stress and tension caused by mechanical, thermal shock and vibration.
  4. Excellent electrical insulation, anti – corona silicone glue for electronics
  5. Excellent outdoor aging, service life can reach 20 to 30 years
  6. stable mechanical and electrical propertiesbetween 60 to 260 ℃

Data Sheet

Properties before curing

ItemUnit Satop®8739
ColorWhite
Viscosity 25℃, mPa·sPaste
Density25℃, g/cm31.53±0.05
Tack free time25℃, 55%RH,min12 ± 5

Properties after curing

ItemUnit Satop®8739
Hardness Shore A50 ± 5
ThermalW/m.K0.40
Elongation at break%350
Tensile strengthMpa2.8
Shear strengthMpa, iron/iron2.2
Dielectric strengthkV/mm(25℃)18
Dissipation factor(1MHz) (25℃)0.09
Dielectric constant(1MHz) (25℃)2.9
Volume resistance(DC500V) Ω· cm2.00E +14

Remark:All the above data come from 25 ℃ and 55% RH glue curing conditions after 7 days. 

Application

Household electrical appliances, seals automobile lamps, seals Industrial components and other mechanical, seal Pv module, seal LED lamp, seal T tube, fixed PCB board and electronic components.

PACKING

  • 310ml/cartridge,25cartridge/carton
  • 2600ml/cartridge,6pcs/caton

Storage and transportation

  1. Avoid light, heat.
  2. This product is non-dangerous goods and is transported it according to general chemicals.
  3. Shelf life is 12 months under 25 ℃. Please take a sample testif more than the storage.

Operation process of silicone glue for electronics

  1. Cleaning surface: cleansurface, remove rust, dust and oil.No need bottom coating to most material, such as glass, metal and most commonly industrial plastics.But on some polymers, it may be less cohesive.For example: polyethylene, polypropylene and PTFE, use PM1200 to do bottom coating.
  2. cut the nozzle to the required size, Fitted with glue gun, squeeze the glue into the cleaned surface and distribute evenly, When bonding, fixed two surface together. Under the conditions of room temperature and 55% relative humidity, adhesive’s surface dry in about 15 minutes, therefore, all processing must be completed before surface dry.
  3. Cured:Cured: place the coated parts in the air and used them after curing for 24 hours at room temperature.
  4. Precautions: after opening SATOP®8739, use it as soon as possible, once again, when used again, squeeze out the solidified part, continue to use, do not affect normal use.
  5. please consult the market departmentif use dispensing equipment

Precautions of silicone glue for electronics

  1. Keep away from children
  2. It is recommended to be used in well-ventilated places.
  3. Wash the skin with soapy water immediately if it touches the skin carelessly.
  4. If you touch your eyes accidentally, rinse immediately with water for a long time and open your eyes. If irritation persists, seek medical attention.

Product safety information is not included here. Before use, please read the product information, product safety information and packaging label for safe use. The product safety information can be obtained from SANTOP and the distributor, or write to the SANTOP service center [email protected] or call 021-64243697.

The technical data of this paper are all typical values obtained under laboratory conditions.We are not responsible for the results of methods beyond our control.Because users use condition is different, different material surface state, curing conditions, storage conditions, transportation and other factors can make gum stability and physical and mechanical properties, the actual performance data has some changes are normal phenomenon.Before using this product,Validation is based on the data provided in this article.If you have any problems with the process, you can contact our technical service department and we will provide you with all the help. Our company reserves the right to modify the data in this article.

  • Client :
  • Construction Date :
  • Investors Website :
  • Location :
  • Value :