ISO9001 ISO14001
    Solution provider with 15 years in adhesive&sealant industry

SATOP6118 transparent epoxy adhesive, metal to metal adhesive

SATOP6118 transparent epoxy adhesive, metal to metal adhesive

Product description

SATOP6118 transparent epoxy adhesive is a kind of epoxy resin adhesive with fast curing speed. This two-component epoxy adhesive is designed to bond ceramic, metal to metal adhesive, glass, plastic, rubber, paper, cloth and other products.

SATOP6118 transparent epoxy adhesive cures without heating. After thoroughly mixing the A component and the B component in a ratio of 3:1 (weight ratio or volume ratio), the product has a long operation time of 2 hours, good foaming property, and a transparent hard protective layer after curing.

The cured glue has the following characteristics:

  • Resists moisture, dirt and other atmospheric components
  • High strength, excellent adhesion
  • Good anti-pollution and low surface pretreatment requirements
  • Solvent free, no cure by-product
  • Stable mechanical and electrical performance between -50 and 120 °C
  • Good adhesion to plastic PC, fiberglass cloth and steel plate

Conventional performance

Test items

Test standard

Unit

SATOP 6118 A/B

 

Part A

Appearance

Visual 

Transparent thick liquid

Viscosity

GB/10247-2008

mPa·s25

10000-13000

Density

GB/T 13354-92

g/cm325

1.10

 

Part B

Appearance

Visual

Transparent liquid

Viscosity

GB/10247-2008

mPa·s25

10-50

Density

GB/T 13354-92

g/cm325

1.10

Operation process

 Items 

Unit or condition

SATOP 6118 A/B

Mix ratio

Weight ratio

3 : 1

Mix ratio

Volume ratio

3 : 1

Mix viscosity

mPa·s25

300-600

Mix Density

g/cm325

1.10

Operation time (1)

min25

120-150

Dead time

min25

150-180

Initial cure time

25℃/hr

24

(1)the operation time was tested with the gluing amount of 60g.

Take the ratio of part A and part B in proportion, stir and mix evenly, quickly apply to the parts that need to be bonded, and quickly cure in a short time.

Operational precautions

  • Manual use of bulk packaging,  it needs to be weighed and stirred quickly when mixing the glue, thismethod is suitable for places where the bubble requirements are not high; otherwise, it is necessary to use a two-component dispenser to mix and apply glue.
  • If the temperature is too low, the curing speed will be too slow. When the initial strength cannot be reached, the constant temperature control on site is needed.
  • The curing process of the glue is an exothermic reaction, and the amount of the glue will affect the length of the operation time. Therefore, the operation time under the glue amount of 60g is only a reference time.

Typical performance

Items

Test standard

Unit

SATOP 6118A/B

hardness

GB/T 531.1-2008

Shore D

82

Shear strength

GB 6328-86

MpaAl/Al

15

Shear strength

GB 6328-86

MpaPC/ PC

10

Expansion coefficient

GB/T 20673-2006

μm/m

44

Bibulous rate

GB/T 8810-2005

24h25%

<0.3

Dielectric strength

GB/T 1693-2007

kV/mm25

>20

Dissipation factor

GB/T 1693-2007

1MHz(25)

0.014

Dielectric constant

GB/T 1693-2007

1MHz(25)

3.53

volume resistance

GB/T 1692-92

DC500VΩ· cm

1.2×1015

Packing

  1. Part A: 1 kg/barrel; Part A: 1 kg/bottle.

Storage and transportation

  1. Part A and Part B should be protected from light, heat, and sealed (can be transported and stored as non-dangerous goods);
  2. Shelf life:1 year(25℃).

Instructions

Product safety information is not included here. Before use, please read the product information, product safety information and packaging label for safe use. The product safety information can be obtained from SATOP and the distributor, or write to the SATOP service center [email protected] or call 021-64243697.

The technical data of this paper are all typical values obtained under laboratory conditions.We are not responsible for the results of methods beyond our control.Because users use condition is different, different material surface state, curing conditions, storage conditions, transportation and other factors can make gum stability and physical and mechanical properties, the actual performance data has some changes are normal phenomenon.Before using this product,Validation is based on the data provided in this article.If you have any problems with the process, you can contact our technical service department and we will provide you with all the help. Our company reserves the right to modify the data in this article.

  • Client :
  • Construction Date :
  • Investors Website :
  • Location :
  • Value :